Recent content by Ole school

  1. O

    401A Signal Generator issues

    Solved it by replacing a bad capacitor in the motor drive box
  2. O

    401A Signal Generator issues

    I have Torchmate 2 Plasma cutter with the old Flashcut 401A signal generator and it will not power on. I have used it 3 years and no issues, Any suggestions on how to troubleshoot it? Thanks
  3. O

    I have the old 401A signal generator and it will not power on. I have used it 3 years and no...

    I have the old 401A signal generator and it will not power on. I have used it 3 years and no issues, Any suggestions on how to troubleshoot it? Thanks
  4. O

    Bearing adjustment on Linear slide cassette

    Dnmeistr-LECS - In searching the forum history I saw where you posted "The bearings in the cassette are adjustable and there is a set screw that will pull the bearings tight, loosen the cassette bolts and pull the 1/4" rubber cover out of the adjusting hole and tighten the set screw found...
  5. O

    Torchmate Cad Cam LT V9 - Having trouble creating tool paths

    Thanks Doug and KCHOGHEAD, my operator said it looks good..... for now
  6. O

    Torchmate Cad Cam LT V9 - Having trouble creating tool paths

    Thanks, How did you connect the tool path?
  7. O

    Torchmate Cad Cam LT V9 - Having trouble creating tool paths

    I have attached the CDL file from torchmate cad cam so you can see what ive done with the toolpaths and cad geometry. I know that you can draw in torchmate but I prefer to draw in autocad some shapes I draw require a lot of layout. I been using autocad for many years and it is simply just much...
  8. O

    Torchmate Cad Cam LT V9 - Having trouble creating tool paths

    Still having trouble creating tool paths. As a test we are trying to cut a square base plate with 4 holes. We have created a file drawn in Auto Cad using Torchmate Cad Cam LT V9 and to my knowledge it is done correctly. We have attached a file and would appreciate if you can open the file and...
  9. O

    Questions - Cad Cam LT V9 Software Torchmate 2 Controller

    Thanks for the help, I'll pass it on to my operator and hopefully put this issue to rest
  10. O

    Questions - Cad Cam LT V9 Software Torchmate 2 Controller

    Cad Cam LT V9 Software Torchmate 2 Controller We are having trouble creating tool paths properly. I am using autocad to draw setting male lines to a layer and setting female lines to a separate layer then saving as a dxf. I then import the dxf into the torchmate cad cam software. I then...
  11. O

    Torchmate Cad Cam Lt V9 questions

    Thanks guys, I was suspecting all along that it didn't have that capability. So we'll have to live with that and my operator just said before we saw Doug's last post, we would have to rotate the drawing etc.. We'll only do that on long cuts
  12. O

    Torchmate Cad Cam Lt V9 questions

    Thanks for the link to the videos but my operator said he still needs to find out how to skew the plate with a x-angle reference,we have the Torchmate 2 controller software.
  13. O

    Torchmate Cad Cam Lt V9 questions

    Thank you Doug, I'll pass that on to my operator
  14. O

    Torchmate Cad Cam Lt V9 questions

    We are tying to set up x- angle to cut a part that is not square with the table. The reason we want to do this is so we don't have worry about cutting directly along on a table slat so we like to angle the plate a little . We need to know how to navigate through the program to do this. We also...
Back
Top